CONTACT PHONE 1-800-548-0054
OPEN HOURS

Mon - Sat 8:00 - 18:00

American Disabilities Act

CAMBER

Camber, as it relates to these kinds of bridges, causes considerable confusion. In this instance, camber is defined as rise at bridge center / bridge length = camber %. The following points should help:

The arch of a truss or girder bridge is not structural. You may specify the bridge with any amount of arch desired, or none at all.

A flat bridge would be specified as “dead load” camber. This indicates to Excel to put enough camber in the members to offset the bridge’s own dead load and a bit extra to offset any creep over time.

In the pre-fabricated bridge industry, positive camber is usually expressed as the percentage of the bridges length that produces “X” rise at the center of the span. This percent is not the deck slope or pitch. Example: A 100′ bridge with “1%” camber will have 1′ of rise at center, but about a 4% slope at the ends. Camber is applied as approximately a radius in the bridge members.

For public use, in order to meet ADA, the general practice is to specify the camber at 1.2% of the length, or “maximum slope per ADA 5%” can be specified, which amounts to the same thing.

To maximize the pleasant arched look and still meet ADA, call out “2% camber” or “maximum slope per ADA 8.3%.” ADA then requires toe plates and pipe ADA hand rails be added. ADA only allows the 8.3% slope continuously for 30′, so on the longer spans this specification will not meet ADA.

Sometimes for aesthetic or clearance reasons, more camber is desired. If ADA is not required, or if an “alternate route” is available to the impaired, 2.5% camber is most often specified. For foot traffic, some architects & engineers contend that camber over 3-5% would be too likely to cause slip and fall problems.

In multiple span bridges, whether continuous or separate simple spans, camber should be expressed as a percentage of the total bridge length. This way Excel’s engineers will be responsible to properly camber each bridge section so it appears as one smooth continuous arch.

If a highly arched appearance is desired, Excel can employ a number of methods to give this aesthetic, depending on the bridge size and the budget.

Please call for an accurate estimate (800) 548-0054 or use our web form for a quick budget price.

Learn more about common pitfalls

    Get a Free Quote

    Allow us to assist you! Complete the form below and provide us with a few particulars for a free & quick budget price. Let us know if you want a friendly representative to call you or simply call us. 800-548-0054


    Your Contact Info:

    First Name:
    (required)

    Last Name:
    (required)

    Company:

    Email:
    (required)

    Phone:
    (required)

    Address:

    City:

    State:

    Postal Code:

    Bridge Details:


    Where will the bridge be delivered to?
    (required)

    What is the length of the bridge (end to end)?
    (required)

    What is the inside clear width? Example
    (required)

    What is the bridge's primary use?
    (required)
    PedestriansPedestrians and Light Vehicles (up to 10,000 lbs)Heavy Vehicles (Such as Emergency Vehicles)I'm not sure. I'd like to speak with a specialist.

    Type of Material

    Is the bridge for public or private (residential) use?
    (required)
    PublicPrivate

    Project Funding
    (required)
    PublicPrivate

    Name of Purchaser / Owner of the bridge?
    (required)

    Other Details / Questions?

    How did you hear about us?

    Privacy Policy


    Note: Form will take approximately 5 seconds to send.


    HAVING TROUBLE WITH THE FORM?
    GIVE US A CALL: 800-548-0054

    Please rest assured, if you find you are not receiving the personal touch you deserve, feel free to contact Craig Vasquez Owner / President for personal assistance. Reach Craig by calling our Main Office West Coast 800-548-0054 number and ask our receptionist to have Craig paged.


    Visit our Sister Company:
    Excel Fabricators manufactures heavy steel plates, guards, mounts, and structures of varying shapes and sizes, all built to spec! With over 60 years experience in all the nuances of heavy steel manufacturing and thousands of satisfied customers to attest, Excel Fabricators desires your business opportunities.


    www.excelfabricators.com